Endian banner

The System Menu

The System menu provides several information about the Endian Hotspot Appliance and its status, and allows to define the network setup and some access modalities (e.g., via SSH or for the Endian support).

The sub-menu on the left-hand side contains the following items, which allow for some basic administration tasks and to monitor the running activities of the Endian Hotspot Appliance.

  • Dashboard - overview of the system and of the connections status.
  • Network configuration - network and network interface configuration.
  • Event notifications - set up of notification via e-mail or SMS.
  • Updates - management of system updates.
  • Support - support request form.
  • Endian Network - Endian Network registration information.
  • Passwords - set system passwords.
  • Web console - a console shell on the browser.
  • SSH access - enable/configure SSH access to the Endian Hotspot Appliance.
  • GUI settings - web interface language settings.
  • Backup - backup or restore Endian Hotspot Appliance settings as well as reset to factory defaults.
  • Shutdown - shutdown or reboot the Endian Hotspot Appliance.
  • License Agreement - a copy of the User License Agreement.

The remainder of this section will describe the various parts that compose the System menu items.

Dashboard

The Dashboard is the default page, the one that is displayed upon every login. It encompasses several boxes (“plugins”) organised in two columns that provide a complete overview of the running system and of its health. The top of each box reports the name of the box. The Dashboard has lately undergone some changes in its usability and new features have been added to improve the interaction with the user. The information visible on screen are updated at regular intervals.

The various plugins can be organized according to the user’s preferences:

  • Drag & Drop. Each of the six boxes can be moved around and rearranged in either of the two columns. While moving, a green rectangular box will preview the position of the plugin.
  • Personalisation. A click on the Show settings link underneath the main bar will open a small table showing the available plugins, their description, and the refresh interval. Any of them can be enabled or not and consequently displayed or not on the Dashboard.

The available plugins and the information they display are described here.

System Information Plugin

It shows several information about the installed system. It usually presents the hostname and domainname of the Endian Hotspot Appliance in the title.

Appliance: The appliance type.

Version: The version of the firmware.

Kernel: The current running kernel.

Uptime: The time since the last reboot.

Update status: A message depending on the Endian Hotspot Appliance status:

  • “up to date”. No updates are available.
  • “update required”. New packages can be installed: A click on the message leads to the Updates page where it is possible to review the list of new packages.
  • “Register for enterprise”. The system has not yet been registered to Endian Network: A click on the message will open the Endian Network page, in which to compile a form to complete the registration.

Maintenance: The remaining days of validity of the maintenance support.

Support access: Whether the support team can access the Endian Hotspot Appliance or not. In the former case, it is also shown the date until the access is granted.

Hardware Information Plugin

It shows the main hardware information of the Endian Hotspot Appliance and the resource availability. All the information are provided with the absolute value (graphically with a small bar and in number at the end of a line) and the percentage of their use. The only exception is the CPU load, which shows only the percentage of use, in graphic and numbers.

CPU x: The load of the CPU, where x represents the CPU number, for those appliance that have more than one CPU.

Memory: The amount of the RAM memory used.

Swap: How much swap disk space is used. A high percentage here usually means there is something not working correctly.

Main disk: The usage of the root partition.

Temp: The space used in the /tmp partition.

Data disk: the usage of the /var partition.

Configuration disk: The space occupied by the partition containing all the Endian Hotspot Appliance services and settings.

Log disk: The amount of space used in the partition containing the logs.

The latter values, showing disk space availability, can vary depending on the appliance, since the data, system, and log partitions may be located in different places.

Warning

A partition on the hard disk (e.g., main disk, data disk, /var/log) shall never have a usage of 95% or more, as this can cause malfunctioning and data loss.

Service Information Plugin

Information about the most important services installed on the Endian Hotspot Appliance, along with their actual status, are displayed by this plugin. For each service is shown the status, either ON or OFF, and a summary of the tasks accomplished during the last hour and the last days. A click on the service’s name expands or collapses additional information on the tasks carried out by the service. For running services, there is the possibility to open in a new window the respective Live Logs. Hence, if some number in the summaries sounds strange (e.g., a number of email rejected that is twice as normal) or not common compared to the normal activities, the logs can be controlled to search for some useful message that has been recorded. The services currently supported by this plugin are:

SMTP Proxy: Statistics about the e-mails processed. The number of e-mail currently in the postfix-queue, of the received e-mails and how many of them were clean, the number of viruses found, and how many e-mails were blocked.

HTTP Proxy: The numbers of cache misses and hits of squid and of the viruses found.

Hint

Inactive services are marked with a red OFF message.

Network Information Plugin

It shows information about the network interfaces of the firewall and the traffic. The upper part of this plugin shows several data about the network interfaces of the Endian Hotspot Appliance: Their name, type, link (Up if a connection is established, Down otherwise) and status (Up if the device is activated, Down if not), and the In- and Outgoing traffic. The latter two data are updated in real-time. When ticking the checkbox near the device name, that device is shown in the graphs underneath. The devices’ name is coloured according to the zone they serve.

The lower part of the plugin contains two charts: The first one shows the incoming traffic, while the second one the outgoing traffic on each of the interfaces chosen. The traffic of each interface is coloured according to the zone it belongs to, different interfaces serving the same zone have different nuances. Bridges built on one device are shown in the same colour as the device. Like the traffic data in the upper part, both charts are updated in real-time.

Hint

Up to six interfaces can be selected and shown in the charts.

Signatures Information plugin

This plugin shows information about the actual status of those services requiring the download of signatures that are installed and enabled on the Endian Hotspot Appliance. In case no signature has been downloaded and no service has already been enabled, the message No recent signature updates found is displayed, otherwise the plugin presents the signatures installed for the variuos daemons and the timestamp (date and time) of the last download. The list includes the signatures for the anti-spyware, and antivirus services.

Network configuration

The configuration of the networks and of the network interfaces serving the zones is fast and easy with this 8-step wizard. It is possible to freely navigate back and forth the step, using the <<< and >>> buttons and even decide at any moment to cancel the actions done so far. Only at the last step it is required to confirm the new settings: In that case, all the changes made will be applied. Note that while applying the new settings, the web interface might not respond for a short period.

The Stealth Uplink mode.

The Stealth Uplink mode represents a new possibility to seamlessly integrate the Endian Hotspot Appliance into an existent network infrastructure without the need to modify the existent routing or firewalling rules.

The Stealth Uplink mode requires a Endian Hotspot Appliance equipped with at least two NIC serving the same zone, which can be GREEN, ORANGE, or BLUE. One of these interfaces routes all the traffic directed from the zone to a gateway and in practice represents the Endian Hotspot Appliance‘s ‘uplink’.

The presence of an explicit interface designated as ‘uplink’ allows to distinguish a direction for the traffic flowing outside the zone served by the Stealth Uplink and to filter it using the outgoing firewall. This is the main difference with the no uplink mode in which there is no possibility to filter outgoing traffic and therefore the application control is not applicable.

The Stealth Uplink operating mode requires a particular set up in the Endian Hotspot Appliance‘s firewall setup.

  • System access rules are handled normally.
  • Port forwarding and Destination NAT rules can also be configured normally. However, being the outgoing interface in the same zone as the internal network, the rules will be applied from both sides of the zone.
  • Source NAT is not applied for outgoing connections in this setup as otherwise the behaviour would not be transparent anymore.
  • The outgoing firewall is used for all the traffic that flows from the zone served by the Stealth Uplink through the NIC designated as uplink, allowing to exploit the abilities of the application control.
  • The interzone firewall is employed for all the remaining traffic between the other zones, if defined. It the Stealth Uplink bridge is composed by three or more interfaces, and hence two or more serve the corresponding zone, also the traffic among these and the other zones can be filtered by the interzone firewall.

Due to the availability of this uplink mode, also the GUI of the network configuration wizard has changed, especially in the first page of the wizard, to clarify the differences among the various uplinks and the configuration options available for each of them.

The 8 steps in which the wizard is divided are:

2/8 - Choose network zones

The Endian Hotspot Appliance separates the networks connected to it into four main zones, as described in this section. At this point the two most important zones - GREEN and RED - have already been encountered during the installation: During this step the network zones for the hotspot (BLUE) and the optional demilitarized zone (DMZ - ORANGE) zone can be configured.

Note

In the Endian Hotspot Appliance, one network interface is reserved for the GREEN zone, one for the BLUE zone on which the hotspot runs and another one has possibly been assigned to the RED zone, if the RED interface requires a network card. This might limit the choices here to the point that the ORANGE zone cannot be enabled, due to lack of additional network interfaces.

3/8 - Network Preferences

This step concerns the configuration of the GREEN zone for the management network, for the BLUE zone for the hotspot network and, if needed, of the ORANGE zone. For each of the enabled zones, the following options can be configured:

IP address

The IP address (such as 192.168.0.1) of the interface, which should not be already in use in the network.

Hint

Good practice suggest that the last octet be 1, since the interface will gather the traffic of the whole subnet.

Remember also that a change in the IP addresses of an Endian Hotspot Appliance, especially in a production environment, might require to adjust additional settings elsewhere.

Warning

When configuring the interfaces of the GREEN zone, make sure to not remain locked out of the web interface! This situation may occur for example when changing the GREEN IP address into one that is not reachable from the current GREEN segment and then saving the settings. In this case the only access to the Endian Hotspot Appliance is via serial console.

Network mask

Define the network mask from a drop-down menu containing the possible masks (e.g., /24 - 255.255.255.0).

Hint

All the devices connected To the same subnet shall have the same netmask to communicate properly.

Additional addresses
Additional IP addresses for different subnets can be added to the interface here.
Interfaces

Map a network interface to a zone, with the following rules:

  1. Each interface can be mapped to only one zone and each zone must have at least one interface.
  2. When more than one interface is assigned to a zone, these interfaces will be bridged together and act as if they were part of a switch.

For each available interface this information is shown:

  • A colored checkbox, showing which zone the interface serves. No color means that the interface is not assigned to any zone.

  • Port, the number of the port.

  • Link, shows the current status by means of icons: linkok -the link is active, nolink -no link or no cable plugged in, linkna -no information from the driver.

  • Description, the interface’s PCI identification string, as returned by lspci. The string is trimmed, but it can be shown by moving the mouse on the ?.

  • MAC, the interface’s MAC address.

  • Device, the logical name of the device.

    Note

    Internally, the Endian Hotspot Appliance handles all zones as bridges, regardless of the number of the assigned interfaces. Therefore, the Linux name of the interfaces is brX, not ethX.

Finally, the system’s host name and domain name can be set in the two text boxes at the bottom of the screen.

Private IP Addresses

It is suggested to follow the standard described in RFC 1918 (which has been recently been updated by RFC 6761) and to use for the zone’s setup only the IP addresses contained in the network segments reserved for private use by the IANA, which are:

10.0.0.0 to 10.255.255.255 (10.0.0.0/8, 16,777,216 addresses)
172.16.0.0 to 172.31.255.255 (172.16.0.0/12, 1,048,576 addresses)
192.168.0.0 to 192.168.255.255 ( 192.168.0.0/16, 65,536 addresses)

This choice avoids incurring in DNS resolution errors, as IP addresses not falling within these ranges are likely to have been reserved by other organisations as their public IPs. Moreover, different IP ranges must be used in the different network segments for each interface, for example:

IP = 192.168.0.1, network mask = /24 - 255.255.255.0 for GREEN
IP = 10.0.0.1, network mask = /24 - 255.255.255.0 for BLUE
IP = 192.168.10.1, network mask = /24 - 255.255.255.0 for ORANGE

Note also the first and the last IP address of a network segment (which are usually .0 and .255) are reserved as the network address and the broadcast address respectively, and must not be assigned to any device.

4/8 - Internet access preferences

This step allows the configuration of the interface chosen in step 1, that connects to the Internet or to any other untrusted network outside Endian Hotspot Appliance.

Depending on the Network mode chosen in step 1, different options are present here. For the No uplink modes, only one option is present.

Default gateway
The IP address of the gateway that will take charge of routing the network traffic flowing outside the zone. The gateway’s IP address must fall within the network in which the Endian Hotspot Appliance is located.

An additional option is available when the Bridged mode has been selected:

Bridged zone
This drop-down menu allows to choose to which zone the traffic will be bridged to, among those that have been activated.

When the network mode is Routed, there are more options available and depend on the selected uplink type. At the bottom of the page appear two options that are commonly available, namely MTU and Spoof MAC address with, described below, and the choice of the DNS resolver, available for almost all interface types, which is wither Dynamic or Manual: In the latter case, one valid IP address of a DNS server must be provided manually in the next step. The other configuration options are:

ETHERNET STATIC
The IP address and network mask of the RED interface, as well as the IP address of the default gateway, that is, the IP address of the gateway that connects the Endian Hotspot Appliance to the Internet or to another untrusted network. Optionally, the Ethernet hardware address (MAC address) of the interface can be specified.
ETHERNET DHCP
Only one available option, namely the DNS choice.
PPPoE

To configure PPPoE, fill in the form with the username and password assigned by the provider, and the authentication method. Optionally, the provider’s service and concentrator name can be configured, though this is usually not needed.

Hint

If unsure whether to select PAP or CHAP authentication, keep the default option.

ANALOG/UMTS Modem

While Endian Hotspot Appliance supports most modern UMTS modems, some care is required when using them in conjunction with Endian Hotspot Appliance. On one side, some UMTS modems are USB mass storage devices as well and usually register two devices (e.g., /dev/ttyUSB0, /dev/ttyUSB1): In this case the first device /dev/ttyUSB0 is the modem, the second one is the storage. These types of modem can cause problems when restarting the firewall because the Endian Hotspot Appliance tries to boot from the USB mass storage device. On the other side, some SIM cards require a personal identification number (PIN) to work, but this is not supported. To allow those cards to work with Endian Hotspot Appliance, the PIN should be removed from the card.

Note

The SIM card must be plugged in when the Endian Hotspot Appliance is turned off.

There are 2 sub-screens for this choice.

  1. In the first one, specify to which serial port the modem is connected to and whether it is an analog modem or an UMTS/HSDPA modem.

    Hint

    The /dev/ttyS0 device is reserved for the serial console and is therefore not available as port for modems.

  2. In the second one, configure the modem’s bit-rate, the dial-up phone number or access point name, the username and password that have been assigned by the provider and the authentication method (if unsure, keep the default PAP or CHAP). For UMTS modems it is also necessary to specify the access point name.

GATEWAY
The IP address of the default gateway - that is, the IP address of the gateway that connects the Endian Hotspot Appliance to the Internet or another untrusted network.

The common options are:

MTU
The MTU size of the packets send over the network.
Spoof MAC address with
Specify a custom MAC address for the RED interface.

The MTU size.

While the vast majority of the ISPs uses a standard value of 1500 bytes, in some circumstances the standard MTU size results too high. If that happens, some strange network behaviours will noticed, like e.g., downloads which always stop after a while or connections which will not work at all.

If the ISP does not use a standard MTU size, it is easy to discover the correct one, by sending special ICMP packets with a specific value, that can be lowered until no errors are encountered: At theist point, the MTU size is correct and this value should be entered in the configuration options.

In order to send the icmp packets do the following:

Log in to the EFW and choose a host which can be actually reached (e.g., the ISP’s DNS, which should always be reachable) and ping that host with the following command:

ping -c1 -M do -s 1460 <host> (please refer to the ping(8) manpage for more info).

If the MTU size 1460 is correct, ping replies like the following one are received:

PING 10.10.10.10 (10.10.10.10) 1460(1488) bytes of data.
1468 bytes from 10.10.10.10: icmp_seq=1 ttl=49 time=75.2 ms

If however the current MTU size is still too big for packets of the size 1460, an error message like this will appear:

PING 10.10.10.10 (62.116.64.82) 1461(1489) bytes of data.
ping: sendmsg: Message too long

Retry with different packet sizes (i.e., the value after the -s option), until the correct size has found and no error is displayed. The value shown within brackets in the ping command’s output is the MTU size. In this example the output is 1460(1488), therefore 1488 is the value to select for the MTU size.

An MTU value lower than 1500 may cause problems also in the OpenVPN setup and require to adjust some setting there.

5/8 - Configure DNS resolver

This step allows to define up to two IP addresses for the DNS server, unless they are assigned automatically: In this case, no configuration option can be set and it is safe to move to the next one. If only one DNS server should be used, the same IP address must be entered twice. The IP address(es) of the DNS must be accessible from the Endian Hotspot Appliance, otherwise URL and domain resolution will not work.

See also

Changes to the RED interface, i.e., the uplink, and the DNS server can be modified later, separately from the other network configuration:

Uplink editor
Menubar ‣ Network ‣ Interfaces ‣ [edit uplink]

6/8 - Configure default admin mail

The configuration of a global administrator e-mail address that will be used by all services to send e-mails, is done here. The administrator e-mail address is then used for notifications, in case of problems or emergencies .These email addresses will be used by the Event notifications.

There are three fields to configure.

Admin email address
A valid e-mail address to which the system e-mails should be sent.
Sender email address
A valid e-mail address that appears as the sender address. A custom sender address proves useful if the recipient wants to filter messages sent by the Endian Hotspot Appliance.
Address of smarthost
The SMTP server through which the email should be sent.

Hint

Although all the fields may be left blank, it is suggested to supply at least one valid Admin e-mail address.

7/8 - Apply configuration

This step informs that the network setup is now finished and all the new settings have been gathered. Clicking on the OK, apply configuration button will save the settings and apply the configuration by restarting all the necessary services and daemons.

8/8 - End

In the last step, all the configuration files are written to the disk, all the devices are reconfigured and the network-depending services and daemons (e.g., the firewall and ntpd) are restarted as necessary. The whole process may take up to 20 seconds, during which the connection to the administration interface and through the Endian Hotspot Appliance may not be possible.

The administration interface will then reload automatically. If the GREENIP address has changed, the GUI will be reloaded at the new IP address. In this case or in case the hostname changed, a new SSL certificate is generated to identify the new host.

Note

To change later only some of the settings in the network configuration (e.g., the hostname or the network range of a zone), simply start the network configuration, skip all the steps until the one in which to make the desired changes, edit the appropriate values, then proceed to the last step and finally save.

Event notifications

Whenever some critical event takes place on the Endian Hotspot Appliance (e.g., a partition is filling up, or there are updates available), there is the option to be immediately informed by e-mail about it and to promptly take some actions to solve a problem, if required.

Three tabs are available in this page: Configuration, Events, and SMS.

Configuration

The Configuration tab contains the basic options to set up the notification of events that take place on the Endian Hotspot Appliance.

To start the event notification functionality, click on the grey swoff.

The options available are the following.

Use default email settings
Tick the checkbox to use the default administrator e-mail address as specified in the Installation wizard or in step 6 of Menubar ‣ System ‣ Network configuration.
Use SMTP proxy service
Tick the checkbox to use the system’s SMTP proxy, if available.

If the previous two options are not selected, the next few options appear.

Email sender address
The e-mail address that appear as the sender of the e-mail.
Email recipient address
The e-mail address to which the e-mail will be delivered.
Use smarthost for email delivery

Tick the checkbox to reveal a couple of options to set up the SMTP server that will be used to send the notification e-mail.

Note

While the SMTP proxy supports encryption, when an external smarthost is used as SMTP Proxy, neither the SSL/TLS nor the STARTTLS protocols can be used.

Smarthost address
The URL of the smarthost.
Smarthost port
The port on which the smarthost listens to.
Smarthost requires authentication
Tick the checkbox if credentials shall be supplied to successfully connect to the smarthost. The next two option will appear.
Smarthost username
The username to be used to authenticate with the smarthost.
Smarthost password
The password associated with the username supplied in the previous option.
Authentication method
Select which method the smart host shall use to authenticate the user.

There are two further options that are used to configure to which telephone number SMS shall be sent.

Destination phone number country prefix
The country code to which the phone number belongs to.
Destination phone number
The actual phone number.

Events

This tab shows a list of all the events that can produce a notification message and allows to configure the actions to be done when each of the events takes place. Right above the list there is a small navigation bar and a search field: The latter can be used to filter only the relevant items.

The list contains five columns:

Event ID

The 8-digit ID ABBCCCCD code of the event, which is built as follows:

  • A represents the layer number, i.e., the system’s component in which the event has taken place:
    • 1 = kernel
    • 2 = system
    • 3 = services
    • 4 = configuration
    • 5 = GUI.
  • BB is the module number
  • CCCC is a sequential number assigned to the event
  • D is the severity of the event, i.e., the degree of badness of the event. The lower the number, the worst the severity:
    • 0 : critical event
    • 1 : an error
    • 4 : a warning
    • 6 : a recovery from a bad state
    • 8 : an informational message.
Description
A short description of the event.
Email
A ticked checkbox means that an e-mail is sent when the event takes place.
SMS
A ticked checkbox means that an SMS is sent when the event takes place.
Actions
The only action available is to modify the corresponding event by clicking on the swedit icon.

When modifying an event, a new panel appears above the list with the following configuration options displayed.

Event ID and Description are unchangeable as they identify the event and are automatically generated by the system.

Send email for this event
By ticking this checkbox, an e-mail will be sent upon the occurrence of the event.
Send SMS for this event
By ticking this checkbox, an SMS will be sent upon the occurrence of the event.

The following table shows the list of all the IDs that correspond to an event. Note that, dependind on the type of appliance, some event may not be occur on the Endian Hotspot Appliance (e.g., on appliances without RAID controllers, events 10100011, 10100026, and 10100038 will never occur).

Event ID Description
10100011 One device of the RAID array failed.
10100026 The rebuild of RAID array has completed.
10100038 Start recovery of RAID array.
20100016 One uplink has gone online.
20100024 One uplink has gone offline.
20100036 The system has started.
20100044 The system has shut down.
20100054 The system is rebooting.
20110030 All uplinks have gone offline.
20110046 All uplinks are online.
20110054 An uplink is dead.
20110066 An Uplink turned back alive.
20200018 An SSH user has successfully logged in from a remote location.
20200024 An SSH user failed to log in from a remote location.
20300014 A disk is getting full.
20400014 An user has failed to log in to the management interface.
20500018 SMS credit alert: only ... SMS left
20600018 Digital Input Rising Trigger on an input
20600028 Digital Input Falling Trigger on an input
20700018 OpenVPN client opened tunnel on an interface
20700218 OpenVPN client closed tunnel on an interface
20800014 An OpenVPN user failed a login failed
20800024 An IPsec/Xauth use failed to login
20800034 An L2TP user failed to login
20800048 An Open VPN user has logged in successfully
20800058 An IPsec/Xauth user has logged in successfully
20800068 An L2TP user has logged in successfully
20800078 An Openvpn user has logged out
20800088 An IPsec/Xauth user has logged out
20500028 SMS credit alert: no SMS left
30100018 The system upgrade has completed successfully.
30100021 The system upgrade has failed.
30100038 There are system updates available.
40100016 The remote access to support user has been revoked.
40100024 The remote access to support users has been granted.
40100034 The access for support user has been extended until ...

SMS

SMS notifications are used either by the hotspot, to verify accounts or by the event notification system to send alerts to the system administrator.

This box is divided into two parts: at the top there it is possible to add SMS bundles, while at the bottom some information about the SMS contingent is displayed.

Enter Activation Code ...
To add a new SMS bundle, it must be first purchased on the Endian Network, after which an activation code will be generated. This activation code must be supplied in this textbox.
Activate
After supplying a valid activation code, clicking on this button will add an SMS contingent that will be used for sending the notifications.
Available SMS
The number of SMS that are at disposal.
Reserved SMS
The number of SMS that have already been used, but not yet delivered to the recipient. This event may occur for example if the recipient was not reachable.

Updates

The management of the software updates is done from here. It is possible at any time to manually check for available updated packages, or to schedule a periodic check.

In this page there are two boxes: One with the current status of the system and one to schedule a routine check for updates.

Status

The Status box informs whether the system needs updates or not. In the former case, a list of available packages is presented, while in the latter the message “Your Endian Hotspot Appliance is up to date!” is displayed. Moreover, additional messages inform of the last date and time when a check for updates and the last upgrade have been carried out. These options are available:

Check for new updates
A manual check for updated packages is started, and any upgradable package found is listed here. Individual packages can be chosen from the list and installed.
Start update process NOW
The update process is launched: The system downloads the updated packages which are then installed, replacing the old ones.

Note

In order to check for updates, a valid maintenance is required, otherwise no update will show up, even if available.

Schedule for retrieving the update list

The Schedule box allow to set up a periodic job, governed by the cron daemon, that retrieves the list of updated packages. The available, mutually exclusive, options are Hourly, Daily, Weekly, and Monthly. Moving the mouse over the small ? next to each option shows a tool-tip with the exact time at which the job will run.

Support

In this page it is possible to manage requests for assistance to the Endian support.

Note

To be able to submit a support request, the system must be registered to the Endian Network. If not, the “Currently no running maintenance available.” message will be displayed.

The page is divided in two boxes with different purposes: The first one containes a link to open the support’s home page, while in the second one it is possible to grant SSH access to the support team.

Visit Support Web Site

This box contains only a hyperlink to the home page of the support.

Please visit our Support Web Site
By clicking on this link, a new tab in the browser will open, where it is possible to find directions on how to fill in an assistance request to the support team.

Access for the Endian Support Team

Optionally, access to the firewall can be grant via SSH, a secure, encrypted connection that allows a member of the support staff to log in to the Endian Hotspot Appliance, verify its configuration and inspect it to find out where the problem lies. The box contains an informative message, the status of the access, which is either DENIED or ALLOWED. When the status is DENIED a button appears at the bottom of the box:

Allow access
Click on this button to grant 4 days of access to the Endian Hotspot Appliance to the support team.

When the support team access is allowed, a new message appears under the status message: Access allowed until: followed by the date and time when access to the Endian Hotspot Appliance will be revoked. Moreover, there are two buttons at the bottom of the box.

Deny access
Immediately revoke the access to the Endian Hotspot Appliance.
Extend access for 4 more days
If the support team needs more time to inspect the Endian Hotspot Appliance, a click on this button extends the access grant by four more days.

Endian Network

If the Endian Hotspot Appliance has been purchased with a maintenance package, it can be registered and connected to the Endian Network, the Endian solution for an easy and centralised monitoring, managing, and upgrading of all the registered Endian Hotspot Appliance systems, with just a few clicks. Note that many functionalities of the Endian Hotspot Appliance (e.g., support, sms notification, and so on) require that the appliance be registered to the Endian Network.

This page is organised into two tabs, namely Subscription and Remote Access.

Subscription

If the firewall has not yet been registered to the Endian Network, the registration form is shown, that can be filled in before submitting the request for registration. After the registration has been completed, the Subscriptions tab shows three boxes:

System information

Basic data about the Endian Hotspot Appliance: Serial number, activation code, model of the appliance, and the maintenance package chosen.

Registration Status

A summary of the Endian Network support status: System name, organisation for which the Endian Hotspot Appliance is registered, system ID, and the date of the last update.

Your Activation Keys

To receive updates from and to participate in the Endian Network, at least one valid (i.e., not expired) activation key is required. There is a key for each support channel, but typically just one, shown with the expiry date and the days of maintenance left. An expired key is shown by its channel name stricken-through and by the expired string in the corresponding Days left column.

Remote Access

The Remote Access tab allows to choose whether the Endian Hotspot Appliance can be reached through the Endian Network and by which protocol. To allow access, click on the grey switch on swoff the top of the page: Its color will turn green, and two access options can be chosen, by ticking the checkbox:

Enable HTTPS access ...
The Endian Hotspot Appliance can be reached via the web interface.
Enable SSH Access ...
Login via a secure shell to the Endian Hotspot Appliance is allowed. Activating this option automatically activates the SSH access.

See also

A step-by-step lesson to register the Endian Hotspot Appliance on the Endian Network is available here.

Passwords

In this page passwords can be changed for each of three default users, by writing each new password twice and then by pressing the corresponding Change Password button:

Admin
The user that can connect to the web interface for administration.
Root
The user that can login to the shell for administration. Logins can be made either via the serial console, or remotely with an SSH client.

Hint

Passwords need to be at least 6 characters long.

Web Console

The web console provides an applet which emulates a terminal within the browser window, that serves as a CLI to carry out administrative tasks.

The functionalities of the web console are the same found upon logging in via serial console or SSH. On the bottom left of the applet, a message shows the status of the console: Connected or Disconnected. It is possible to exit at any time by typing exit in the console and then pressing Enter on the keyboard, like in any normal console.

When disconnected, click again on the Web console sub-menu item to reconnect. On the bottom right of the applet, two hyperlinks show up:

Enable virtual keyboard.

When clicking on this link, a keyboard applet appears below the console, that can be used to type and execute commands by clicking the mouse on the various keys.

Note

When the web console is disconnected, this applet does not communicate with the console.

Disable input

This link toggles the possibility to send input from the keyboard to the web console.

Hint

This option has no effect on the virtual keyboard.

SSH access

This screens allows to enable remote SSH access to the Endian Hotspot Appliance. This is disabled by default and it is the recommended setting. There are two boxes in the page: Secure Shell Access Settings and SSH host keys.

Secure Shell Access Settings

The SSH access is activated by clicking on the grey switch swoff. The SSH service is started, and after a few seconds, some configuration options are displayed:

SSH protocol version 1

This is only needed for old SSH clients that do not support newer versions of the SSH protocol.

Warning

The activation of the SSH version 1 is strongly discouraged, since this version is not maintained anymore, deprecated, and contains well known vulnerabilities that could be exploited by malicious users. SSH clients nowadays shall always use version 2 of SSH, which is more secure and reliable.

Allow TCP forwarding
Ticking this option lets other protocols be tunneled through SSH. See SYS-1 example for a sample use case.
Allow password based authentication
Permit logins using password authentication.
Allow public key based authentication
Logins with public keys are allowed. The public keys of the clients that can login using key authentication must be added to the file /root/.ssh/authorized_keys.
Save
Click on this button at the bottom of the box to save the setting of the above four options.

Note

The SSH access is automatically activated when at least one of the following options is true:

  • Endian support team access is allowed in Menubar ‣ System ‣ Support.
  • High availability is enabled in Menubar ‣ -Services -> High Availability.
  • SSH access is enabled in Menubar ‣ System ‣ Endian Network ‣ Remote Access.

SSH host keys

At the bottom of the page, a box details the public SSH host keys of the Endian Hotspot Appliance, that have been generated during the first start of the openSSH server, along with their fingerprints and their size in bits.

GUI settings

Two configuration options for the GUI are present here. The first option is the language that will be used for the section names, the labels, and all the strings used in the web interface and can be selected from a drop-down menu. The languages currently supported are: English, German, Italian, Simplified Chinese, Japanese, Portuguese, Russian, Spanish, and Turkish.

The second option is to display the hostname of the Endian Hotspot Appliance in the browser’s window title, activated by ticking the checkbox Display hostname in window title.

Backup

In this section the management of the backups can be carried out: Creation of backups of the current Endian Hotspot Appliance configuration and system rollback to one of these backups when needed. Backups can be saved locally on the Endian Hotspot Appliance host, on a USB stick, or downloaded to a workstation.

It is also possible to reset the configuration to factory defaults, to create fully automated backups, and to carry out various other administrative tasks concerning backups.

This section is organised into two tabs, Backup and Scheduled backups: The former is used to manage manual backups, while the latter to set up automatic, scheduled backups.

Backup

In the Backup tab there are four boxes, that allow to manage the manual backups.

Backup sets

The first box contains a list of the backups stored on the Endian Hotspot Appliance - both manually and scheduled ones, an option to create a new backup, and the legend of the symbols that accompany each backup. If a USB stick is plugged in in the Endian Hotspot Appliance and detected, also backups stored on it are displayed.

When clicking on the Create new Backup button, a dialogue box opens up in which to select the data to be included in the backup.

Current configuration
The backup contains all the configuration settings, including all the changes and customisation done so far, or, in other words, all the content of the /var/efw directory.
Include database dumps

The content of the database will also be backed up. This includes all the hotspot data, such as users and tickets.

Warning

The database dumps may contain sensitive data, so whenever a backup contains a database dump, make sure that it is stored in a safe place.

Include log files
Include the current log files (e.g., /var/log/messages, but not log files of the previous days.
Include log archives
Include also older log files, that have been rotated, like e.g., /var/log/messages.YYYYMMDD.gz, etc. Backups created with this option may become very big after some time.
Include hardware data
Include hardware specific information such as the order of the network interfaces. This is useful mostly for software installations where the order in which network interfaces appear might not correspond to the physical order and hence manual adjustments are necessary. Choosing this will render the backup incompatible to other installations.
Remark
A comment about the backup, that will appear in the Remark column of the table. Hence, it should be meaningful enough to allow a quick recall of the content.

At least one of the checkbox must be ticked to create a new backup.

The format and name of the backup files.

Backup files are created as tar.gz archives, using standard Linux’s tools tar and gzip. The files stored in the archive can be extracted using the tar zxf archivename.tar.gz or tar vzxf archivename.tar.gz to see all the file processed and extracted and see some informative message on the screen, the v option meaning verbose. The name of the backup file is created to be unique and it conveys the maximum information possible about its content, therefore it can become quite a long string, like e.g., backup-20130208093337-myappliance.mydomain-settings-db-logs-logarchive.tar.gz, in which 20130208093337 is the timestamp of the backup’s creation, in the form YYYYMMDDHHMMSS -in this example, 8th of February 2013 at 9:33:37 AM. This choice allows the backups to be lexicographically ordered from the oldest one to the most recent one; myappliance.mydomain are the Endian Hotspot Appliance‘s hostname and domainname as set in Step 3 of the Network configuration (Menubar ‣ System ‣ Network configuration), and settings-db-logs-logarchive represent the content of the backup. In this case it is a full backup, since all four parts appear in the name. For example, a backup containing only settings and logs will be identified by the string settings-logs.

In order to create a backup on a USB external drive, a USB drive (even a stick) must be plugged in in the Endian Hotspot Appliance. It is suggested to use a FAT32/VFAT filesystem, as this maximises portability to other systems. When the stick is detected, the message USB stick detected will appear on the right-hand side of the box, along with a new option Create backup on USB stick. The checkbox next to this option must be ticked for the backup to be stored on the stick.

Click on the Create Backup button to create the backup. After a short time, during which the files required by the backup are gathered and assembled into the archive, the new backup appears in the list. The end of the backup process is marked by a yellow callout that appears above the box, showing the message Backup completed successfully.

The list of available backups, which is initially empty, presents for every backup the creation date, the content shown by a set of letters, the remark, and the list of actions available on each backup file. Automatic backups are marked with the string Auto - backup before upgrade.

The content of each backup is marked by at least one of the following letters or symbols, corresponding to the option specified during its creation:

A, Archive. The backup contains archived log files.

C, Cron. The backup has been created automatically by a scheduled backup job.

D, Database dumps. The backup contains a database dump.

E, Encrypted. The backup file is encrypted.

H, Hardware data. The backup contains hardware specific information.

L, Log files. The backup contains today’s log files.

S, Settings. The backup contains the configurations and settings.

U, USB. The backup has been saved to a USB stick.

!, Error. Something did not succeed while sending the backup file by email.

The available actions are to export download an archive to the local workstation, to delete it delete, or to restore it reload on the Endian Hotspot Appliance.

Encrypt backup archives

The second box makes available the option to encrypt all the backups by providing a GPG public key. Select the GPG public key by clicking on the Choose file button to upload the key file from the local file system. Make sure the checkbox Encrypt backup archives is ticked, then upload the key file by clicking on Save.

Hint

Encrypt backup archives whenever saving sensible data in the backup file, like for example the passwords of users stored in the database or hotspot’s users data and billing information.

Import backup archive

The third box lets a previously saved backup archive be uploaded to the Endian Hotspot Appliance. The backup file can be selected by clicking on the Choose file button and then choosing the backup file from the local file system. Optionally, some note to the backup can be added in the Remark field. Finally, the backup is uploaded by clicking on the Import button. The backup appears after a short period in the backup list at the top of the page, and can be restored by clicking on the restore icon reload.

Note

It is not possible to import encrypted backups on the Endian Hotspot Appliance: Any encrypted backup must be decrypted before being uploaded.

Reset configuration to factory defaults and reboot

The fourth box allows to wipe out all configurations and settings done so far and reboot the system with the default configuration. This result is achieved by clicking on the Factory defaults button: The configuration of the Endian Hotspot Appliance is reset to the factory defaults and rebooted immediately, right after a backup copy of the current settings has automatically been saved.

Scheduled backups

Automated backups of the system can be enabled and configured in the Scheduled backups tab, which contains two boxes.

Scheduled automatic backups

In the first box, automatic backups are enabled and configured. When enabled, the elements of the Endian Hotspot Appliance to be included in the backup can be chosen as seen in the Backup Sets box in the other tab. The only difference is that for scheduled backups there is no possibility to specify a remark. Additional options are:

Enabled
Enable scheduled backups.
Keep # of archives
Choose from the drop-down how many backups to keep on the Endian Hotspot Appliance (from 2 up to 10, but they can be exported to save space).
Schedule for automatic backups
The frequency between backups, either hourly, daily, weekly, or monthly.

Send backups via email

In the second box, the system can be configured to send or not the backups by e-mail. The following otpions are available.

Enabled
Allows backup archives to be sent via e-mail.
email address of recipient
The e-mail address to which to send the e-mail with the backup.
email address of sender
The e-mail address that will appear as the sender’s e-mail address, which proves useful when backups should appear to have been sent from a special address (say, backups@myappliance.mydomain), and must be provided if the domain or hostname are not resolvable by the DNS.
Address of smarthost to be used
The address of a smarthost to be used to send the e-mails, which is needed in case the outgoing e-mails should go through a SMTP server, like, e.g., the Company’s SMTP server, rather than to be sent directly by the Endian Hotspot Appliance.
Send a backup now
A click on this button will save the settings and immediately try to send an e-mail with the backup’s archive as attachment, ab action that serves also as a test for the correctness of the data supplied.

See also

A guide to create a backup on a USB stick.

Shutdown

Option to either shutdown or reboot the Endian Hotspot Appliance, by clicking on the Shutdown or the Reboot button respectively, are provided in this page.

Warning

The shutdown or reboot process starts immediately after clicking on the respective button, with no further confirmation request.

After a reboot, it is possible to continue to use the GUI without the necessity of an authentication.

License Agreement

This section displays the license agreement between Endian and the owner of the Endian Hotspot Appliance.

Note

After an upgrade, if the license agreement changes, at the first login it is necessary to accept the new license agreement before accessing the upgraded system and being allowed to use the Endian Hotspot Appliance